To run cgminer as a regular user you should also install the udev rules: Libusb-1.0-0-dev is already the newest version.Ġ upgraded, 0 newly installed, 0 to remove and 1 not upgraded. Libusb-1.0-0 is already the newest version. Note, selecting ‘libusb-1.0-0-dev’ for regex ‘libusb-1.0’ Note, selecting ‘libusb-1.0-0’ for regex ‘libusb-1.0’
:/home/pi/workarea/cgminer# sudo apt-get install libusbĮ: Unable to locate package sudo apt-get install libusb-1.0 configure: line 11925: -pthread: command not foundĬonfigure: error: “udev support requested but libudev not installed”Ĭonfigure: error. The stream ends with:Ĭhecking whether gcc and cc understand -c and -o together… yes I fixed the -Wall switch and retried the command. | #define PACKAGE_BUGREPORT “ ”Ĭonfigure:3939: error: in `/home/pi/workarea/cgminer’:Ĭonfigure:3941: error: C compiler cannot create executablesĪny ideas? Be gentle, I am new to all this… Gcc: error: unrecognized option ‘-qversion’Ĭonfigure:3870: checking whether the C compiler worksĬonfigure:3892: gcc -O2 -WAll -march=native conftest.c >&5Ĭc1: error: bad value (native) for -march switchĬc1: error: unrecognized command line option ‘-WAll’ When I look at config.log, I see the following: configure –enable-bflscĬhecking build system type… armv6l-unknown-linux-gnueabihfĬhecking host system type… armv6l-unknown-linux-gnueabihfĬhecking target system type… armv6l-unknown-linux-gnueabihfĬhecking for a BSD-compatible install… /usr/bin/install -cĬhecking whether build environment is sane… yesĬhecking for a thread-safe mkdir -p… /bin/mkdir -pĬhecking whether make supports nested variables… yesĬhecking for style of include used by make… GNUĬhecking whether the C compiler works… noĬonfigure: error: in `/home/pi/workarea/cgminer’:Ĭonfigure: error: C compiler cannot create executables :/home/pi/workarea/cgminer# CFLAGS=”-O2 -WAll -march=native”. also my ASIC Miner Block Erupters led is off but it was solid the whole time i was setting it up.This sequence doesn’t compile on my RPi. The top isn't refreshing the hash rate so i dont know how its doing but the bottom (start nonce, start voltage, and start freq) part just keeps looping with different values.Īnd when i go to slushes pool dashbord it doenst say any of my workers are going. SB management ool management ettings isplay options uit im working with slush's pool and using putty to conect to my pi.
That follows this tutorial and everything worked smoothly. If you found this useful, I accept Bitcoin donations by following this link.
And if your Pi is failing to communicate with your Antminer U3 via cgminer, unplug and reconnect the USB cable. You can also SSH into your Pi at any time and run sudo screen -x cgminer to view your cgminer screen. You can play around with voltage and frequencies by following the table in the official manual, found here, there's no real need to change what I suggested above though. My Antminer U3 is running at around ~59-60Gh/s, hopefully yours should be the same.
RASPBERRY PI CGMINER NOT FINDING DEVICE PASSWORD
cgminer -bmsc-options 115200:0.57 -o POOL -u USERNAME -p PASSWORD -bmsc-voltage 0800 -bmsc-freq 1286 Sudo nano /etc/rc.local - remember, Ctrl-X to exit, then type Y and press Enter to save changes.Īdd this just above exit 0, again enter your own pool, username and password: Now, add cgminer to start automatically when the Pi is powered on and create a screen session: Test cgminer is working correctly by running the following (input your own pool, username and password): Install, configure and also enable bmsc options:Įxport LIBCURL_CFLAGS=’-I/usr/include/curl’ Sudo apt-get install libusb-1.0-0-dev libusb-1.0-0 libcurl4-openssl-dev libncurses5-dev libudev-dev screen libtool automake pkg-config libjansson-dev screen Login via PuTTY with the default username/password, then raspi-config if you would like to change the hostname, default password and so on. Run a fresh install of Raspbian using NOOBS, after the install type ifconfig and make a note of the IP address, so that you can remotely SSH into your Pi. That link is useless if you're running an Antminer U3, here's how I got mine working using screen and PuTTY.
0 kommentar(er)
